- Loading...
Page History
...
VirtualThreads.allThreads() (and JDWP VirtualMachine/AllThreads) enumerates all active live platform threads, virtual threads are not enumerated unless the JDWP agent is started with the includevirtualthreads option (see below).
For thread dumps and troubleshooting purposes the debugger can invoke the com.sun.management.ThreadsHotSpotDiagnosticMXBean.dumpThreads API in the target VM to enumerate threadsgenerate a thread dump. This can be used as stop-gap solution until there is better support for structured debugging finding virtual threads in the debugger APIs.
Thread groups
Virtual threads are not active members of a thread group.
JDI ThreadGroupReference::threads (and JDWP ThreadGroupReference/Children) enumerate all active live platform threads in a group, virtual threads are not enumerated.
...
ThreadStartRequest/ThreadDeathRequest define a new method to control whether thread start/end events are sent for all threads or only platform threads.
...
JDI ThreadReference defines isVirtual() to test if a thread is a virtual thread.
JDWP ThreadReference/IsVirtual is the equivalent.
Testing if target VM supports virtual threads
The following recommend way is temporary, to allow debuggers to distinguish JDK 17 EA builds from Loom EA builds.JDI VirtualMachine defines supportVirtualThreads() to test to check if the target VM supports virtual threads.The supportsVirtualThread boolean in the reply to the JDWP CapabilitiesNew command is the equivalentis version 19 or later. There is no way to determine if --enable-preview was set, but this is also unnecessary. The JDK 19 debug agent will still execute commands that are virtual thread specific, even if the JVM was not run with --enable-preview.
Not Supported
The following are not currently supported for virtual threads:
- JDI ThreadReference.stop
- interrupt
...
...
As a temporary solution to allow existing debuggers work with virtual threads, the JDWP agent will track virtual threads so they can be enumerated for debuggers that want to enumerate all virtual threads. The options that control this behavior are:
...
- enumeratevthreads control whether or not virtual threads are included in list of threads returned by JDWP VirtualThread.GetAllThreads command.
- trackvthreads controls which virtual threads will be returned when enumeratevthreads=y.
- fakevthreadstartevent is independent of the two others. If y, then before sending an event, send a fake THREAD_START event for if the debugger hasn’t already been notified about the virtual thread that the event occurs on. Note currently there is a bug, and if trackvthreads=all, no fake THREAD_START will ever be sent. This is only an issue if the debug agent is started after some virtual threads have been created.
...
JDWP agent options
As a temporary solution to allow existing debuggers to work with virtual threads, the JDWP agent will track virtual threads so they can be enumerated for debuggers that want to enumerate all virtual threads. The options option that control controls this behavior areis:
| Option Name and Value | Description | Default |
|---|
| includevirtualthreads=y|n |
| List of all threads includes virtual threads as well as platform threads | n |
- enumeratevthreads control includevirtualthreads control whether or not virtual threads are included in the list of threads returned by JDWP VirtualThread.GetAllThreads and ThreadGroupReference.Children commands. This flag can be turned on for compatibility purposes. This flag will may eventually go away and the debug agent will operate as if it was set to 'n'. Note that the debug agent will only return virtual threads that are created after the debugger attaches. If the debugger detaches, the debug agent will forget about all discovered virtual threads, and the list will once again be empty when the debugger attaches again.
- [notifyvthreads has been removed. To disable THREAD_START and THREAD_END events for vthreads, use the PlatformThreadsOnly filter as described in this section] notifyvthreads controls whether or not THREAD_START and THREAD_END events are sent for vthreadsvirtual threads. The default is to send them. The purpose is to allow debugger writers to set to 'n' use notifyvthreads=n to see how the debugger works without getting these events. This is meant as a short term convenience flag rather than having to set the filter as described above. In the long run Once support for notifyvthreads=n is gone, if debuggers don't want these eventswant THREAD_START and THREAD_END events for virtual threads, they will need to set the filter. When using the PlatformThreadsOnly filter. Since this means no , the debugger can learn about virtual threads when events are delivered for them, such as a BreakpointEvent. Since no THREAD_END event will be sent for the virtual thread, the debugger will then need to figure out how to "forget" about virtual Threads that the virtual threads it is tracking when they have terminated. This could possibly be done with an ObjectReference.IsCollected commanda ThreadDeathRequest that filters on the virtual thread. This would need to be done for each virtual thread being tracked by the debugger. Please note that notifyvthreads=y will not override any PlatformThreadsOnly filter that is in place.
Issues with too many virtual threads hitting breakpoints
Each running virtual thread is mounted on a carrier thread. There are a limited number of carrier threads (usually defaulting to the number of available cores). When a virtual thread hits a debugger breakpoint, it pins its carrier thread, preventing any other virtual thread from running on it. If you have an application with a large number of virtual threads, and you setup a breakpoint that many virtual threads will hit, you can wind up in a situation where every carrier thread is running a virtual thread that is at a breakpoint. No virtual threads will make progress when this happens. Those that are mounted are all at breakpoints, and those that unmounted have no carrier thread to run on. If you resume one of the virtual threads, when it yields it will allow unmounted virtual thread to run, which likely itself will then hit this same breakpoint, leaving back to having all virtual threads being stuck.
If you single step in one of these virtual threads that are at a breakpoint, single stepping will work until you step over a call that can lead to the virtual thread yielding. At this point the virtual thread is umounted and a new one can run on the carrier thread (once again, likely quickly hitting the same breakpoint). It will appear that the single step has failed to ever complete. In reality it is waiting for the yielding virtual thread to be remounted and start running again. This can't happen until a carrier thread is freed up. Thus you'll find that you need to start resuming various virtual threads that are at breakpoints until eventually one of them yields AND its carrier thread is used to mount and run the single stepping virtual thread. There's no telling how many virtual threads at breakpoints you will need to resume before this happens.
It is possible to avoid getting into this situation. The first thing to do is to setup the breakpoint so that it suspends all threads rather than just the event thread. This way you'll never have more than one virtual thread hitting the breakpoint at the same time. If you do this, you also need to make sure to setup the debugger's single stepping "thread resumption policy" to resume all threads, rather than just the single stepping thread. If you take these two steps, breakpoints and single stepping should work much better when dealing with a large number of virtual threads that can hit the same breakpoint.
Links
Project Loom Early Access builds
...
Overview
Content Tools